> How To Reset Netgear Router

How To Reset Netgear Router

A reset should be done if your router does not work properly. The following issues might cause with your router. If the router’s wireless signal is not strong enough, then the device might not function properly. If you have forgotten your password to connect, then you should reset your router with the following guide how to reset Netgear router. Also, if the Wi-Fi card is not detected, reset your router. This issue may occur if network drivers aren’t installed properly. The place where you have positioned your router might not receive a proper signal. This will also lead to the router not working issue. Hardware issues might also refrain the router from working properly. If any Operating system corruption has occurred, the router will fail to work.

Problems That Occur With Netgear?

  • The Netgear router might be turned off.
  • It might not connect to the access page on entering the password.
  • The router might at times receive a weak signal.
  • The Wi-Fi card might not fit in properly.
  • The place where the router has been positioned should be changed if you receive weak signals there.
  • It will not turn on if there is no proper power supply.
  • Check if the power cord is associated properly.

Quick Steps For How To Reset Netgear Router

  • Before resetting your router, check if you have turned it on.
  • Turn your router so that you face the back side of it.
  • Search for the Reset button to reset your router to its default settings.
  • Make use of a paper clip to press the Reset button and hold it for at least seven seconds.
  • Release the button and wait for at least 7-10 seconds. The router will start rebooting.
  • The Power light will start blinking once the reset process starts.
  • After the completion of the process, it will stop flickering.
  • The Netgear router will now be reset to its default settings.

Steps To Reset A Netgear Router Using 4 Steps

FIND THE “RESET” BUTTON

Netgear routers possess a Reset button that can be used to reset when an error occurs. The Reset button will be present at the back side of the router. Go near the router and make sure you are looking at the back side of it. The Reset button will be present with a label under it.

INSERT A PAPER CLIP INTO THE RECESS.

For how to reset the Netgear router, the reset button is very small and cannot be handled easily with your hands. You should make use of a paper clip or pin to press the Reset button. Search for a paper clip. Once you find it, bend it slightly. Insert it into the Reset button.

TAP THE RESET BUTTON AND HOLD IT FOR 7 SECONDS

Insert the paper clip into the Reset button and hold it for at least 7 seconds. Hold it firmly without dropping it. If you drop it halfway through the process, then it will be canceled. So, ensure that you press it for the entire time specified here.

RELEASING THE “RESET” BUTTON

After holding the Reset button for 15 seconds to 20 seconds, release it. Eject the paper clip slowly in the backward direction to release the button. Removing it fast might cause damage to the Reset button. The Reset process will begin after you release the button.

How To Reset Netgear Router To Factory Default Settings

How To Soft Reset Using Netgear Router Dashboard

  • Initially, associate your router with the computer with the help of an Ethernet cable.
  • You can connect them using a modem in between.
  • Open the web browser on your computer and go to the search bar.
  • Key in 192.168.1.1 or 192.168.1.1 in the address bar. These are the default IP addresses of the router.
  • Else, go to www.routerlogin.net
  • Enter the User name and password in the respective fields when prompted.
  • After you have logged in successfully, go to the Maintenance tab present under the Settings Backup option.
  • Click the Erase option to delete the backup settings and the router will be reset to its default settings.
  • After the reset process is over, log in again and navigate to the Maintenance tab.
  • Choose the Diagnostics tab and then select the Reboot option present.

How to Hard Reset Using The Reset Key

  • Hard reset is a simple process. Follow the guidelines mentioned below to how to reset the Netgear router.
  • Make sure your router is connected to the power supply.
  • Turn on your Netgear router.
  • At the backside of the Netgear router, you will find a Reset key.
  • Search for a paper clip and bend it slightly so that you can insert it properly.
  • Hold the paper clip by the other end and insert it into the Reset key and hold it for at least 45 seconds.
  • Release it and then restart the router.
  • Along with it, restart your modem and wait patiently for a minute.
  • Set up the Netgear router again to use it.

How To Find Netgear Password

  • Forgetting the Netgear router’s password is common, and it can be solved easily.
  • You can either find it or reset your password to get access to the router.
  • To find your password, go to the browser and type http://www.routerlogin.net in the search bar.
  • The default user name & password is Admin and Password.
  • If you are unable to login with these details, then you must reset your password.
  • For resetting the password, key in the address specified above and hit Enter.
  • Press the Cancel button. Enter the serial number of the router when a prompt appears.
  • Click the Continue option and answer the security questions in the proceeding screen.
  • Tap the Continue option. Enter the new password in the next screen.
  • Click the next option and the password will be successfully reset.
  • The Login option should be selected to sign in to the router’s access page.

How To Find Out The Netgear Router’s Password

  • Turn on your computer.
  • Open your default browser on the computer. Key-in http://www.routerlogin.net in the address bar.
  • When a prompt appears asking you to enter the Username and Password, do the same.
  • The default User name is Admin, and the password is Password.
  • Enter it in the respective fields provided to you and click the OK option.
  • On entering it correctly, you will get access to the Home Page.
  • This procedure gives you the correct username and Password.
  • The default password will be printed at the back of the router.
  • You can make use of that password to access the home page of the router.
  • Look at the documentation that has come along with your router for the password.
  • If you have connected the router to your computer, then you can find the password from it.
  • Right-click on the Wireless Network icon present at the bottom right corner of the screen.
  • Select the Network and Sharing Center to open it.
  • Tap the name of the current Wi-Fi network and then choose Wireless Properties.
  • Select the Security tab and tick the Show Characters checkbox to view the hidden password.
  • The password will be displayed on your screen.
  • Use that to login to the router’s access page.

Reset Password On Netgear Wireless Router

  • Open your browser after turning on your computer.
  • Go to the search bar and type www.routerlogin.net.
  • Click the Cancel option.
  • In case you have enabled password recovery, then you will be asked to specify the serial number of your router.
  • The serial number will be available on the label stuck on the product.
  • Tap the Continue option, and you have to provide answers to security questions.
  • Enter the answers that you have already saved.
  • You have to click the Continue button again. In the next screen that is displayed, you will be prompted to enter the password of the router.
  • Specify the new password as per your choice and tap the Confirm button.
  • Key in a new set of security questions after changing the password.
  • Select the Next button, and the router password will be reset by using the manual of how to reset Netgear router.
  • Press the Login button to sign in with your new password.

How To Change Netgear Wifi Password

  • Switch on your system.
  • Launch your web browser from the home screen.
  • Specify http://www.routerlogin.net in the search bar as the query and hit the Enter button.
  • In the next window, enter the username and password of the router.
  • The default username and password are Admin, Password respectively.
  • Tap the OK option after entering it. You will be directed to your router’s homepage.
  • Choose the Wireless tab available on the home page.
  • In the name(SSID) field, enter your new user name.
  • Go to the Password (Network Key) field, and key-in the password in the respective field.
  • Tap the Apply button after entering the username and password.
  • Your user name and password is now changed.

192.168.1.1 Netgear Router Setup Process

  • Here, you can get to know how to connect your Netgear router to the Internet.
  • First, associate your modem with the Netgear router.
  • Attach your computer to any one of the available LAN ports.
  • The next step is to switch off the router, modem, and the computer. Wait for some time and then turn it on.
  • After the booting up process gets over, launch the default web browser on your computer.
  • Go to the search bar and type http://192.168.0.1 or http://192.168.1.1. These are the two commonly assigned IP address for routers.
  • You will be prompted to log in. The default credentials need to be entered.
  • Username and password that you enter are case-sensitive. So make sure you type them correctly.
  • If you have set a password of your own, enter it. If you don’t remember the password you set, then reset the router to log in using the default password with the guide of how to reset Netgear router.
  • Tap Setup Wizard in the next screen. The wizard screen will be displayed on your computer.
  • Click the Yes option and tap the Next button.
  • In the proceeding step, the setup wizard will detect the type of Internet connection that you use.
  • In case of a cable Internet connection, the wizard will find a Dynamic IP address.
  • Click the Next option on the router to save the settings.
  • Note: The default settings should not be changed unless you have the DNS information given by your Internet Service Provider.
  • To verify if your router has been connected to the internet, choose the Router status option under the Maintenance tab.
  • Check the IP address information present there. A valid address should be entered.

Configure And Reset Your Netgear WGR614V9 Router

  • Firstly, connect your router to the modem and then associate your computer to it.
  • After you connect it successfully, you have to configure the router.
  • The configuration includes the wireless setup also. You have to associate the router to a wireless network.
  • To reset your router, perform the steps mentioned below.
  • Turn on the router so that you face its backside.
  • Search for the Reset button and press it.
  • Take a paper clip and bend it slightly. Insert it into the Reset button.
  • Hold it for at least 7 to 10 seconds. Release it after 10 seconds and the reset process will start.

How To Reset DGN2000 OR DG834GV5 Router?

  • The above-specified models do not have a Reset button.
  • Once you reset the router, your configuration will be lost.
  • Configurations such as user name, password, and other settings will also be erased.
  • If you can manage to lose the configuration, then you can proceed to the Reset process.
  • Follow the guidelines below to reset the DGN2000 or DG834Gv5 router.
  • Press the Wireless on/off button and the WPS button simultaneously.
  • Hold it for at least 6 seconds until the LED below the Power button starts blinking.
  • After 6 seconds, you have to release the Wireless on/off button and the WPS button.[Research source]
  • Wait until the router reboots.
  • Now you can configure any settings according to your choice.

How To Reset The Username And Password On Netgear Router

In The Web Interface

  • You can change your password with the help of Smart wizard.
  • Turn on your computer and launch the default web browser.
  • On the search bar, key in http://routerlogin.net. Wait until you are directed to that page.
  • Enter the User name and Password of the router when a prompt appears.
  • For most routers, the default credentials are Admin and password respectively.
  • Tap the Wireless Settings tab present under the Setup option at the left side of the window.
  • In the text box provided for the name(SSID) and passphrase, you have to enter the new password and name.
  • Click the Apply option to change the password.

With The Restore Factory Settings Button

Click on the Apply button.

Locate the Reset button at the back side of the router and press it to start how to reset the Netgear router.

Take a paper clip and bend it. Insert it into the Reset button and hold it for 6 seconds.

Release it after six seconds and the reset process will start.

After the reset process is complete, open the web browser on your system.

Type http://routerlogin.net in the search bar of the browser.

On the login window, enter the username and Password of the router.

On the home page, choose the Administration option present under the Advanced tab.

Select the Set Password option to change your password.

First, type your old password and then key in the new password twice.

Select the Enable Password Recovery option to recover your password in the future if you lose it.

Leave a Comment